3D MODEL DESCRIPTION
Classic silhouette, bold colors, and a launcher that gives it real distance. A throwback that actually performs.
Glider Plane
- This STL file is recommended for FDM Printers!
- 3D Printing Time : Monocolor - 36 Minutes* (may vary according to your printer model)
Multicolor - 01 Hour 56 Minutes* (may vary according to your printer model and the amount of colors in your AMS, in this print we’ve used 02 colors) - Approximately Height: 0.6 cm
*Note: Printing time based on a Bambu P1s printer, according to our tests.
WARNING: Do not remove the plane while the print bed is still hot. Removing it while the bed is hot may cause the plane to warp.
3D PRINT SETTINGS (FOR 0.4 MM NOZZLE)
- Line Width/ Nozzle: 0.4 mm
- First Layer Line Width: 0.48 mm / 120%
- Average Speed: 20mm/s (First Layer) / 50mm/s (All the other layers) (Ender like) | 20 mm/s (First Layer) / 250 mm/s (All the other layers on Bambu Lab)
- Recommended Initial Layer Height: 0.2 mm
- Recommended Layer Height: 0.2 mm
- Recommended Perimeters/ Walls: 3.
- Recommended Infill (%): 5% (Gyroid)
- Needs Support: No.
- Build Plate Adhesion: No.
Launcher
- This STL file is recommended for FDM Printers!
- 3D Printing Time : Monocolor - 03 Hours 34 Minutes* (may vary according to your printer model)
Multicolor - 21 Hours 24 Minutes* (may vary according to your printer model and the amount of colors in your AMS, in this print we’ve used 02 colors) - Approximately Height: 9 cm
*Note: Printing time based on a Bambu P1s printer, according to our tests.
Will you need;
Rubber Band N°8: Amazon - Mercado Livre
Note: These links are purchase suggestions, and are products similar to those we use in our development and testing. Variations may occur. Pay attention to the measurements indicated and/or assembly instructions to ensure correct fitting.
ATTENTION: Requires super glue.
3D PRINT SETTINGS (FOR 0.4 MM NOZZLE)
- Line Width/ Nozzle: 0.4 mm
- First Layer Line Width: 0.48 mm / 120%
- Average Speed: 20mm/s (First Layer) / 50mm/s (All the other layers) (Ender like) | 20 mm/s (First Layer) / 250 mm/s (All the other layers on Bambu Lab)
- Recommended Initial Layer Height: 0.2 mm
- Recommended Layer Height: 0.2 mm
- Recommended Perimeters/ Walls: 4.
- Recommended Infill (%): 10% (Gyroid)
- Needs Support: Yes (tree), and set the option “On Build Plate Only”.
- Build Plate Adhesion: Yes, only in the “Float” parts.
Stand
- This STL file is recommended for FDM Printers!
- 3D Printing Time : Monocolor - 01 Hours 22 Minutes* (may vary according to your printer model)
Multiparts - 01 Hours 47 Minutes* (may vary according to your printer model)
Multicolor - 01 Hours 50 Minutes* (may vary according to your printer model and the amount of colors in your AMS, in this print we’ve used 02 colors) - Approximately Height: 8 cm
*Note: Printing time based on a Bambu P1s printer, according to our tests.
ATTENTION: “Multipart” files requires super glue.
3D PRINT SETTINGS (FOR 0.4 MM NOZZLE)
- Line Width/ Nozzle: 0.4 mm
- First Layer Line Width: 0.48 mm / 120%
- Average Speed: 20mm/s (First Layer) / 50mm/s (All the other layers) (Ender like) | 20 mm/s (First Layer) / 250 mm/s (All the other layers on Bambu Lab)
- Recommended Initial Layer Height: 0.2 mm
- Recommended Layer Height: 0.2 mm
- Recommended Perimeters/ Walls: 3.
- Recommended Infill (%): 5% (Gyroid)
- Needs Support: No.
- Build Plate Adhesion: Yes (Brim), only in “Neck multipart” file.
The parameters above are recommendations made by our staff; if you prefer, you can adapt them according to your preferences.
Happy Printing!
